KALM - Rod end with male thread, left-hand thread - igus

CAD model selection

	1
	2
	3
	4
	5
	6
	7
	8
	9
	10
	11
	12
	13
	14
	15
	16

		LINA Bill of material	ARTNR Part no. ⁿ/ₐ	SZK Max. static tensile strength Short term [N]	SZL Max. static tensile strength Long term [N]	QK Max. radial load Short term [N]	QL Max. radial load Long term [N]	EG Minimal thread depth [mm]	ADA Max. torque strength outside thread [Nm]	ADOM Max. torque through Ball without metal sleeve [Nm]	ADMM Max. torque through Ball with metal sleeve [Nm]	D1 E10-Diameter [mm]	D2 Diameter [mm]	D3 Thread ⁿ/ₐ	C1 Width [mm]	B Width [mm]	H Height [mm]	I1 Length [mm]	I2 Height [mm]	SW1 Max. swivel angle [°]

		KALM-05	KALM-05	800	400	80	40	13	0.4	5	12	5.00	18	M5	6.0	8	33	19	42	30
		KALM-06	KALM-06	1000	500	100	50	15	0.5	10	15	6.00	20	M6	7.0	9	36	21	46	29
		KALM-08	KALM-08	1700	850	200	100	18	2.0	12	40	8.00	24	M8	9.0	12	42	25	55	25
		KALM-10	KALM-10	2500	1250	300	150	20	5.0	20	50	10.00	30	M10	10.5	14	48	28	63	25
		KALM-10 F	KALM-10 F	2500	1250	300	150	20	3.0	20	50	10.00	30	M10x1.25	10.5	14	48	28	63	25
		KALM-12	KALM-12	2700	1350	400	200	22	6.0	30	70	12.00	34	M12	12.0	16	54	32	71	25
		KALM-12 F	KALM-12 F	2700	1350	400	200	22	6.0	30	70	12.00	34	M12x1.25	12.0	16	54	32	71	25
		KALM-14	KALM-14	3400	1700	700	350	25	12.0	35	75	14.00	38	M14	13.5	19	61	36	79	25
		KALM-16	KALM-16	3900	1950	800	400	26	17.0	40	110	16.00	42	M16	15.0	21	66	37	88	23
		KALM-16 F	KALM-16 F	3900	1950	800	400	26	17.0	40	110	16.00	42	M16x1.5	15.0	21	66	37	88	23
		KALM-18	KALM-18	4200	2100	1000	500	29	20.0	45	150	18.00	46	M18x1.5	16.5	23	72	41	96	23
		KALM-20	KALM-20	6000	3000	1300	650	32	25.0	55	200	20.00	50	M20x1.5	18.0	25	78	45	104	23
		KALM-20 M20	KALM-20 M20	6000	3000	1300	650	32	25.0	55	200	20.00	50	M20x2.5	18.0	25	78	45	104	23
		KALM-22	KALM-22	7200	3600	1500	750	34	25.0	60	-	22.00	56	M22x1.5	20.0	28	84	48	112	22
		KALM-25	KALM-25	7500	3750	1900	950	39	45.0	65	-	25.00	61	M24x2.0	22.0	31	95	55	126	22
		KALM-30	KALM-30	8800	4400	2300	1150	46	85.0	70	-	30.00	71	M30x2.0	25.0	37	112	66	147	22

Additional Information

Loading ...

Users who viewed this, were also interested in

iglidur® X - type S - Sleeve bearings, inch sizes

iglidur® X - type S - Sleeve bearings, inch sizesigus 30.01.2024

DryLin® SHT - Basic

DryLin® SHT - Basicigus 12.09.2022

KBRM CL - Rod end bearing with female thread with hexagonal housing, right-hand thread, 2nd generation

KBRM CL - Rod end bearing with female thread with hexagonal housing, right-...igus 01.02.2024

drylin® E Kupplungen - Claw couplings

drylin® E Kupplungen - Claw couplingsigus 20.07.2021

iglidur® A500 - type F - Flange bearings, metric sizes

iglidur® A500 - type F - Flange bearings, metric sizesigus 30.01.2024

WLM - Pressfit Bearing, mm

WLM - Pressfit Bearing, mmigus 19.01.2021

TJUM-01 - Split Linear Bearing, mm

TJUM-01 - Split Linear Bearing, mmigus 20.07.2021

JFRM-ZB - Zero backlash lead screw nuts

JFRM-ZB - Zero backlash lead screw nutsigus 01.05.2020

SWZ-W-208 - Lead screw nuts with axial locks

SWZ-W-208 - Lead screw nuts with axial locksigus 13.09.2022

Hybrid carriage with rollers - Round

Hybrid carriage with rollers - Roundigus 09.09.2022

EWUMN - Low Level Supported Stainless Steel Shafts 1.4125, mm

EWUMN - Low Level Supported Stainless Steel Shafts 1.4125, mmigus 12.09.2022

SWUM - Supported Steel Shafts, mm

SWUM - Supported Steel Shafts, mmigus 12.09.2022

WA - Shaft End Block, Standard Design, mm

WA - Shaft End Block, Standard Design, mmigus 12.09.2022

iglidur® A500 - type S - Sleeve bearings, metric sizes

iglidur® A500 - type S - Sleeve bearings, metric sizesigus 30.01.2024